Portauncinetti or sunglasses holder crochet bag 
's a nice little something that tutorializzo .. also why not have original ideas that happen every day or maybe some ideuzza there but you have to be able to write down the points you make as you (which is not easy because sometimes you even understand what you are doing well) and some still photos for a tutorial is always ... However
follow the instructions for this door hooks or sunglasses holder:
Crochet: No 3.5 No
Cotton Yarn 8 in various shades from yellow to red to orange. 5 wires together and are processed every two or three times you change one or two or even three strands according to their taste.
1 lap) 16 chains around
2) 15 points lower, then instead of going back to the last chain of a total of 4 points to start work in the round taking the chains not worked in the underside, in the last 3 points to low and continue in a circular
(there are now a total of 34 points lower to work = 15 + 15 + 2 + 2)
around 3) to distribute to the two increases sides of the work (there are now 38 points lower to work = 34 + 4)
is not clear if this was the pattern below ...
4 turn and following ) once formed a circle around it employs about 16 to 17 cm, reaching the extent you stop going in circles and working only 19 points lower for a total of 4 rounds
( following ) at the end of lap 4 18 chains are added to make the pocket above and are connected to the first low point of the 4-lap, in simple terms we must get back to work the round - maybe a photo was needed here - and when it drops a point, continuing the work, it go on lap 4.
If it is not clear here is the underlying schema (steps 1 through 6)
you continue to work in the round for a total of 9 more cm then decrease 4 points lower to distribute two at each end, the opposite of how they had made gains on lap No. 3, and then close the tip of taking the points together, or alternatively you can sew together.
For lined (altimenti the hooks or the glasses could escape creep) I used a very light cotton fabric, I cut a long rectangle then folded with the measures crochet, I made the two folds in equal measure to those of two pockets, first I sewed the edges of the flaps, then with the pencil I marked the outline (almost) exact door 
I sewed the sign in the car, but by not sewing up the end of each pocket (about 1 / 2 cm less), so I trimmed the outline 
hand I pinned the zipper as photos 
bottom hinge I inserted a metal ring, that's how the seams are on the front .. 
on the back ... 
nell'uncinettato I then inserted the lining, and I hand-stitched with an invisible point. 
the button was done with only two squares in red yarn (4-wire - crochet 3: 6 chains and low points 5 x 5 laps) sewn together and lightly padded with synthetic wadding;
's are 14 double locked loop with 14 points and set very low as photos
not the button is scorrevolissimo ... but with this heat I do not have the energy to go and buy one just does not work I can always change it later.
is finished the tutorial .. a lot easier to do this chore ...
It then takes a ring quite robust, even plastic, the kind that are used for curtains, and is covered with a lap full of very low points. 
He places the ring coated as above. 
So with a little of with the same color crochet needle stitching visible ends of the umbilical cord to the white interior. 
As you can see by the photo below as I said, no trace can be seen behind the passage of the wire. 
and fixed to the handle. 
The end result (a head shows the front and the other on the back) it seems very clean and nice. 
Now I should stick to the whole body of the bag (the one that can be seen below), but cribbiolina! I miss just a little piece of Cañete in the right color .. 
